Nov 16, 2026

Light Goes Sideways: Understanding Side View LEDs and Their Applications

SIDE VIEW LED · BEGINNER'S GUIDE

Side view LEDs can be found behind indicators on the sides of devices and illuminated buttons on slim panels. Start with the direction of light to understand where they can be used.

For readers new to LEDs | Approx. 5-minute read
01 / THE BASICS

What Is a Side View LED?

An LED is an electronic component that converts electrical energy into light. Besides color and brightness, there is another practical question to ask when selecting an LED:Which direction should the light shine?

A typical top view LED emits light mainly upward from the circuit board, while a side view LED emits light mainly sideways, along the board. This circuit board is commonly called a PCB, short for printed circuit board.

Think of an LED as a small flashlight mounted on a circuit board:
Top view shines upward; side view shines sideways. Different light directions suit different enclosure layouts and light guide structures.

Top View | Mainly Upward

Printed Circuit Board Light

Side View | Mainly Sideways

Printed Circuit Board Light
Figure 1 | Side cross-sections comparing the main light emission directions. These conceptual illustrations do not represent actual package dimensions or radiation patterns. Refer to the datasheet for each product.

Side view describes the direction of light emission, rather than a specific color, brightness, or size. Performance can vary considerably between side view LED models.

02 / APPLICATIONS

Where Can Side View LEDs Be Used?

Side view LEDs are worth considering when the light output needs to be beside the PCB or when light must enter the edge of a light guide. The following two examples illustrate these uses.

STATUS
APPLICATION 01

Side-Facing Indicators: Make Device Status Visible

A circuit board may lie flat inside a device, while users need to view indicators from the front or side. A side view LED can face an indicator opening in the enclosure to provide visual signals for power, connectivity, or faults.

Potential applications:Routers, switches, industrial controllers, and small electronic devices. Suitability depends on the relative positions of the PCB and the enclosure opening.

Panel Backlighting
APPLICATION 02

Slim Panel Backlighting: Illuminate Text and Symbols from the Edge

Buttons, icons, and small display areas can use an edge-lit backlighting design. An LED is placed along the edge of a light guide film or plate, allowing light to enter the guide before optical features direct it toward the surface.

This arrangement can suit panels with limited thickness. However,adding an LED does not automatically make the entire panel glow evenly; the light guide structure, extraction pattern, reflector, and diffuser materials can all affect the final appearance.

Potential applications:Appliance control panels, membrane keypads, backlit laptop keyboards, LCD backlights, e-readers, and smart home control interfaces, among others.

Text / Icon Panel LED Light Guide Plate Extraction features direct light upward; the reflector below recycles downward light.
Figure 2 | Simplified cross-section of edge-lit backlighting. Actual layers and light paths vary by design. Light uniformity must be verified with samples.
03 / SELECTION BASICS

Three Things to Check When Selecting a Side View LED

First decide where the light needs to be visible, then work back to the LED position and specifications. This makes it easier to find a suitable solution than looking at brightness figures alone.

CHECK 01

Does the Light Align with the Opening?

Check whether the emitting face and optical center height align with the enclosure opening or light guide entrance. A package that fits mechanically may still have a misaligned light path.

CHECK 02

Is the Indicator Clearly Visible?

Evaluate color and brightness based on viewing angle, ambient light, and enclosure light transmission. Values measured at different test currents, viewing angles, or in different units should not be compared directly.

CHECK 03

Does the Assembled Result Meet Expectations?

Use assembled samples to check brightness, uniformity, light leakage, and optical crosstalk, while accounting for assembly tolerances. The appearance of an individual LED may differ from its appearance in the finished product.

Tip for beginners:When discussing LED selection, prepare a diagram showing the PCB and enclosure positions, available space, required color, and intended viewing position. This helps make the discussion more effective.

04 / FREQUENTLY ASKED QUESTIONS

Questions You May Have Before Getting Started

Are Side View LEDs Always Brighter Than Top View LEDs?

No. Side view and top view mainly describe the direction of light emission. Brightness still depends on the model, drive conditions, and optical design. Compare products under the same test conditions and verify their appearance in the finished device.

Does Every Side View LED Need a Light Pipe?

No. If the LED can face the enclosure opening directly and provides the required visibility, it may work as a direct indicator. Consider a light pipe when the indicator location is farther from the LED or the light path needs to turn.

Can One LED Illuminate an Entire Panel Evenly?

Not necessarily. Panel area, shape, materials, and light guide design all affect the result. Larger areas may require multiple LEDs or changes to the extraction features. Confirm performance through optical design and sample testing.

Can a Top View LED Be Replaced Directly with a Side View LED?

Usually, simply replacing the component is not enough. In addition to the package and solder pads, check the light emission direction, optical center height, electrical requirements, and enclosure layout.

Further Reading and Technical Resources

This article provides an introduction to general principles and applications. All illustrations are conceptual. Refer to the relevant product datasheet for specific dimensions, optical and electrical characteristics, and operating conditions.